SPECIFICATIONS

EXPAND ALL COLLAPSE ALL

  • Engine

    Model Komatsu SSDA16V159-E2
    Fuel Diesel
    Number of cylinders 16
    Operating Cycle 4 cycle
    Horsepower, Gross 1492 kW / 2000 HP
    Horsepower, Net 1405 kW / 1884 HP
    Rated RPM 1900

  • Body

    Standard body is a steel flat floor body with horizontal bolsters and full canopy. Eyebrow, rear wheel rock ejectors, body up sling and rubber mounts on frame are standard. 

    Standard Capacity, heaped (2:1 SAE)   111 m3
    Body weight 28169 kg

     

    Optional bodies available
     

     

    Floor sheet - Outer 1379 MPa tensile strength steel 16 mm
    Floor sheet - Centre 1379 MPa tensile strength steel 19 mm
    Front sheet 1379 MPa tensile strength steel 10 mm
    Side sheet 1379 MPa tensile strength steel 8 mm
    Canopy sheet 690 MPa tensile strength steel 6 mm

  • Braking System

    Standard ISO3450/1996
    Service brake - front Hydraulically actuated, wheel speed disc, three calipers on a 1213mm O.D. disc
    Service brake - rear Hydraulically actuated, dual disc armature speed, two 635 mm O.D. discs per side, one caliper per disc
    Emergency brakes Automatically applied prior to hydraulic system pressure dropping below level required to meet secondary stopping requirements
    Wheel brake locks Switch-activated
    Parking brakes Spring-applied, hydraulically released, with speed application protection
    Electric dynamic retarder (max.) 2387 kW / 3200 HP. Continuously rated high-density blown grids with retard at engine idle and retard in reverse propulsion

  • Cab

    Standard

    ISO3471 (ROPS)

    ISO3449 (FOPS)

  • Cooling System

    L&M radiator assembly, split-flow, with deaerator-type top tank

    Radiator frontal area 4.65 m2

  • Electric Drive

    AC/DC Current

    Alternator GTA-49
    Dual impeller in-line blower 393 m3/min
    Control AC Torque Control System
    Motorised wheels GEB35 Induction Traction Motors
    Ratio 30.8:1
    Speed (maximum) 64.5 km/h

  • Electric System

    4 x 8D 1450 CCA, 12 volt, in series/parallel, 220 Ah batteries, bumper-mounted with disconnect switch

    Alternator 24 V, 250 A
    Lighting 24 V
    Cranking motors Two 24 V

  • Frame

    Advanced technology, full butt-welded box sectional ladder-type frame with integral ROPS supports, integral front bumper, rear tubular cross members, steel castings at all critical stress transition zones, rugged continuous horsecollar

    Plate material 482.6 MPa tensile strength steel
    Casting material 620.5 MPa tensile strength steel
    Rail width 280 mm
    Rail depth (minimum) 797 mm
    Top and bottom plate thickness 32 mm
    Side plate thickness 19 mm
    Drive axle mounting Pin and spherical bushing
    Drive axle alignment Swing link between frame and axle

  • Hydraulic System

    Steering Accumulator assisted with twin double acting cylinders provide constant rate steering. Secondary steering automatically supplied by accumulator
    Turning circle diameter (SAE) 27.2 m
    Reservoir 511 ltr
    Filtration In-line replacement elements
    Suction Single, full-flow, 100 mesh
    Hoist and steering Dual, in-line, high pressure
    Brake component cabinet Above deck, easily accessible with diagnostic test connections
    Hoist Two 3-stage dual-acting outboard cylinders, internal cushion valve, over-centre dampening
    Hoist times:  
    Power-up loaded 19 sec
    Power-down 10.5 sec
    Float-down empty 12 sec
    Pumps: Two pumps, single package, end of alternator
    Hoist and brake cooling Tandem gear pump with output of 666 ltr/min at 1900 rpm and 18961 kPa
    Steering and brake Pressure-compensating piston pump with output of 254 ltr/min at 1900 rpm and 19134 kPa
    System relief pressures:  
    Hoist 17237 kPa
    Steering and brake 27580 kPa

  • Service Capacities

    Cooling system 441 ltr
    Crankcase 223 ltr
    Hydraulic system 795 ltr
    Motor gear box (each) 38 ltr
    Fuel 3028 ltr

  • Suspension

    Variable rate hydro-pneumatic with integral rebound control

    Max. front stroke: 312 mm
    Max. rear stroke 279 mm
    Max. rear axle oscillation ±5.3°

  • Tyres and Rims

    Rock service, tubeless, standard tyres 37.00 R57
    Flange Mount Rim 27” x 57” x 6”   Rim Assembly
    Rim Rating 758 kPa cold inflation pressure
    Optional Tyres   40.00R57,  42/90R57
    Optional Rim  29” x 57” x 6” Rim Assembly

  • Weight (Approximate)

    Empty and Gross Weight:

    Empty weight 146963 kg
    Gross vehicle weight 328401 kg

     

     

    Weight Distribution:

    Empty:
    Front axle 50%
    Rear axle 50%
    Loaded:
    Front axle 33.6%
    Rear axle 66.4%

730E-8 Dump Trucks

The 730E-8 haul truck is Komatsu’s smallest AC-drive truck model. The truck is rated at a nominal 181 tonne payload capacity and is powered by a 1492 kW/2,000 Hp engine. Although smaller in stature, the unit boasts similar features and technology that is offered in the larger mining truck models. The cabin offers improved operator comfort through reductions in noise and whole of body vibration levels. The frame incorporates structural casting enhancements to ensure chassis longevity beyond industry expectations. Machine systems are designed with inherent reliability in-mind and improved maintainability features deliver high levels of long term dependable mechanical availability. The unit comes standard with our Komtrax Plus remote monitoring and location system, backed by our Australia-wide service and support network. 

  • 1,492 kW / 2,000 HP
    ENGINE POWER
  • 328,401 kg
    OPERATING WEIGHT
  • 181,000 kg
    PAYLOAD CAPACITY

730E-8 Dump Trucks

Current Offers

Reduced Maintenance Intensity and Improved Reliability

The 730E has a reputation for reliability, durability and ease of maintenance. The latest model features a brushless and contactorless AC drive system. The model also incorporates developments that reduce repair time, increase intervals between PM servicing and increase mean time between planned component replacement intervals.

Structurally Enhanced Frame Design

By using advanced computer-aided design, finite element analysis, and full-scale dynamic and static testing, the frame design has been structurally enhanced to carry more weight and provides the highest structural reliability in the industry.

Environmental Footprint Reduction

The latest developments in engine and drive system platforms include features that result in a reduced fuel consumption, reduction in particulate matter emissions and noise emissions. The engine can be configured with optional aftertreatments to meet stringent Tier 4 emission compliances. Electronically controlled fuel injection and improved vehicle filtration systems reduce fluid consumption rates and waste management costs.

Take the next steps

CONTACT US

SIGN UP TO OFFERS & NEWS

FIND US
Cookies are small text files created by a web browser when a user visits a website. Cookies are stored on your device. Some cookies are only stored for the duration of your site visit whilst others are stored for longer periods of time. The information stored in a cookie is transferred between a website and the browser to provide enhanced functionality and improve the user experience when using the website. Komatsu may collect certain information such as browser type and operating system through the use of cookies to improve your experience. You acknowledge this by using our website